Talk:Ball grid array

This is the talk page for discussing improvements to the Ball grid array article.
This is not a forum for general discussion of the article's subject.

Put new text under old text. Click here to start a new topic.
New to Wikipedia? Welcome! Learn to edit; get help.

Article policies

Find sources: Google (books · news · scholar · free images · WP refs) · FENS · JSTOR · TWL

This article has not yet been rated on Wikipedia's content assessment scale.
It is of interest to the following WikiProjects:

Please add the quality rating to the {{WikiProject banner shell}} template instead of this project banner. See WP:PIQA for details.

Electronics Start‑class Low‑importance

	Electronics portal This article is part of WikiProject Electronics, an attempt to provide a standard approach to writing articles about electronics on Wikipedia. If you would like to participate, you can choose to edit the article attached to this page, or visit the project page, where you can join the project and see a list of open tasks. Leave messages at the project talk pageElectronicsWikipedia:WikiProject ElectronicsTemplate:WikiProject Electronicselectronic
Start	This article has been rated as Start-class on Wikipedia's content assessment scale.
Low	This article has been rated as Low-importance on the project's importance scale.

I put some sample instructions for re-balling and it has been removed! It is useful and relevant information. Please justify.

I just added an xray photo of the BGA joints - does that help? DJGB 09:29, 11 October 2006 (UTC)[reply]

No further comments, so I'm going to remove the cleanup tag DJGB 10:24, 31 October 2006 (UTC)[reply]

Do not touch the balls?

Does anybody knows, whether it is possible to test a BGA housing (contacting the balls) and afterwards to solder it normally to a PCB. Or is the BGA destroyed by testing, which would be a disadvantage as it would not be possible to do a final product verification of a BGA packaged device. Michilans (talk) 16:30, 2 December 2008 (UTC)[reply]

 I can think of no reason why not. ICs are tested all the time.

Sharper X-ray

There is a much sharper X-ray image at /media/wikipedia/commons/6/61/X-Ray_USB-Stick_Intenso_High-Speed_32GB_broken.jpg It is still unclear (to me at least) how the bond wires reach the balls. 69.239.104.44 (talk) 13:50, 18 June 2010 (UTC)[reply]

History?

If someone knows and have a bit to tell about the development of the BGA package. Please add it & references. Electron9 (talk) 20:40, 22 March 2008 (UTC)[reply]

uBGA/μBGA/micro BGA/TinyBGA(TM)

What about these? For example, what's the exact difference between BGA & uBGA ? Like, if pitch is bigger than 0.5mm it's BGA, but if it's 0.5mm or smaller it's uBGA, or what?

If you remove the solder, from a BGA chip, are there bumps, or just pads ? Like a PCB has it's pads flat against the board substrate. --DaveDodgy (talk) 14:05, 23 April 2008 (UTC)[reply]

Finest pitch

What's the finest pitch a (μ)BGA chip has been made ? As in, the width of the pad & the spacing between pads (centres, not edge to edge).--DaveDodgy (talk) 18:25, 10 May 2008 (UTC)[reply]

Sometimes?

Article: "BGAs do not have this problem, because the solder is sometimes factory-applied to the package in exactly the right amount." So, do they sometimes not have the problem because sometimes this is done and sometimes for other reasons? Or do they sometimes have the problem because the factory didn't apply the solder? --128.197.11.28 (talk) 14:51, 4 August 2008 (UTC)[reply]

External links

Some external links is useless for article. Need cleanup...--Berserkerus (talk) 16:05, 15 November 2008 (UTC)[reply]

Most of the external links were useless. All except for one have been removed. Rilak (talk) 05:58, 16 November 2008 (UTC)[reply]

BGA lineage

The first sentence of the Discussion section is "The BGA is descended from the pin grid array (PGA)". I disagree. Soldering and inserting pins into sockets are two different ways of making electrical connections, but one is not a descendant of another anymore than a car is a descendant of a horse (two different means of transportation).

Additionally, the grammar is incorrect: "is descended" should be changed either to "is a descendant" or to just "descended". —Preceding unsigned comment added by 74.96.187.144 (talk) 18:51, 14 November 2009 (UTC)[reply]