Jump to content

Phase-shift oscillator

From Wikipedia, the free encyclopedia
This is an old revision of this page, as edited by Glrx (talk | contribs) at 17:48, 25 April 2017 (Op-amp implementation: fix math). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

A phase-shift oscillator is a linear electronic oscillator circuit that produces a sine wave output. It consists of an inverting amplifier element such as a transistor or op amp with its output fed back to its input through a phase-shift network consisting of resistors and capacitors in a ladder network. The feedback network 'shifts' the phase of the amplifier output by 180 degrees at the oscillation frequency to give positive feedback.[1] Phase-shift oscillators are often used at audio frequency as audio oscillators.

The filter produces a phase shift that increases with frequency. It must have a maximum phase shift of more than 180 degrees at high frequencies so the phase shift at the desired oscillation frequency can be 180 degrees. The most common phase-shift network cascades three identical resistor-capacitor stages that produce a phase shift of zero at low frequencies and 270° at high frequencies.

Implementations

Circuit diagram for phase-shift oscillator using a BJT

Bipolar implementation

The implementation using NPN type bipolar transistor is based on example from popular electronics hobby magazine. The circuit generates a sinusoidal wave at its output. The RC phase-shift network is used to form a positive feedback loop. Resistor Rb provides base bias current. Resistor Rc is the collector load resistor for the collector current. Resistor Rs isolates the circuit from the external load. The circuit is taken from [2]

Circuit diagram for phase-shift oscillator using a JFET

FET implementation

The circuit implements the RC phase shift oscillator with FET. Note that the topology used for positive feedback is voltage series feedback.

Op-amp implementation

Circuit diagram for a phase-shift oscillator using an op-amp

The implementation of the phase-shift oscillator shown in the diagram uses an operational amplifier (op-amp), three capacitors and four resistors.

The circuit's modeling equations for the oscillation frequency and oscillation criterion are complicated because each RC stage loads the preceding ones. The equations are simpler when all the resistors (except the negative feedback resistor) and all the capacitors have the same values. In the diagram, if R1=R2=R3=R and C1=C2=C3=C, then:

and the oscillation criterion is:[citation needed]

Without the simplification of all the resistors and capacitors having the same values, the calculations become more complex:

Oscillation criterion:

As with other feedback oscillators, when the power is applied to the circuit, thermal electrical noise in the circuit or the turn-on transient provides an initial signal to start oscillations. The oscillations grow rapidly in amplitude until saturation of the op-amp or transistor limits the gain, and they stabilize at a constant amplitude at which the loop gain of the circuit is unity.

One potential problem with the single op-amp circuit is the high gain required to maintain the oscillation. If it is assumed that each RC segment does not affect the other, a gain of about 8 to 10 will be sufficient to enable oscillation. As mentioned previously, each RC section loads the next section, and a larger gain (about 27 to 30) is required to keep the circuit in oscillation.[3] An improved version of this circuit can be made by putting an op-amp buffer between each RC stage. (This also simplifies the calculations.) Тhe voltage gain of the inverting channel is always unity or equal to 1.

When the oscillation frequency is high enough to be near the amplifier's cutoff frequency, the amplifier will contribute significant phase shift itself, which will add to the phase shift of the feedback network. Therefore the circuit will oscillate at a frequency at which the phase shift of the feedback filter is less than 180 degrees.

References

  1. ^ http://hyperphysics.phy-astr.gsu.edu/hbase/electronic/oscphas.html
  2. ^ K.W.(Widelski?) (1984). Kalejdoskop Techniki. Warsaw, Poland: NOT Sigma.
  3. ^ Mancini, Ron (2002). Op Amps For Everyone (PDF). Dallas, Texas: Texas Instruments. pp. 15–15, 15–16. SLOD006B.