Current injection technique
It is proposed that this article be deleted because of the following concern:
If you can address this concern by improving, copyediting, sourcing, renaming, or merging the page, please edit this page and do so. You may remove this message if you improve the article or otherwise object to deletion for any reason. Although not required, you are encouraged to explain why you object to the deletion, either in your edit summary or on the talk page. If this template is removed, do not replace it. This message has remained in place for seven days, so the article may be deleted without further notice. Find sources: "Current injection technique" – news · newspapers · books · scholar · JSTOR Nominator: Please consider notifying the author/project: {{subst:proposed deletion notify|Current injection technique|concern=Likely copyvio of published work}} ~~~~Timestamp: 20090511103438 10:34, 11 May 2009 (UTC) Administrators: delete |
The current injection technique was developed and published by Dr S. Eio of Staffordshire University (United Knigdom) in 2007.
Abstract The Turn-OFF switching transient of Silicon based power bipolar semiconductor devices is known to limit the device switching speed. This is due to the stored charge in the device during the forward conduction state. Different techniques have been used to minimise this, but all result in a trade-OFF between the ON-state loss and the switching speed.
A novel current injection technique examined in this thesis is aimed at optimising the switching transient of power diodes, thyristors and Insulated Gate Bipolar Transistors (IGBTs) without the need of changing the structure of these devices. To implement this technique, a current injection circuit has been developed with results indicating that the injection of an additional current can reduce the reverse recovery charge of a given power diode and thyristor, and also reduce the tail current of an IGBT.
Test results on diodes and thyristors showed that the amplitude of the injected current required is proportional to the peak reverse recovery current and proved that these devices experience a momentary increase in recombination of current carriers during the injection of the additional current. This help to prevent the device from conducting large negative current, which in turn reduce its reverse recovery charge and reverse recovery time. Results obtained from experiments with an IGBT showed a significant reduction in the time where current falls to zero when opposing current was injected into the device during its turn-off transient. Further simulation results from numerical modelling showed that the injected opposing current temporary increase recombination in the device and therefore reduce the extracted excess carriers that was stored within the device.
To prevent circuit commutation and bonding between the current injection circuit and the maiused. In summary, the proposed technique makes it possible to use devices with low forward voltage drop for high frequency applications. This also imply cheaper cost of devices as less processing steps are required during the manufacturing stages where the need of carrier lifetime control techniques are reduced.n test circuit where the Device under Test (DUT) is connected to, a non-invasive circuit was developed to magnetically couple the two circuits. This removed the need for the semiconductor device used in the current injection circuit to have high breakdown voltage rating and also provided electrical isolation. Typical application of this technique in an inductive load chopper circuit showed a significant reduction in the IGBT tail current, and the reverse recovery time and charge of the freewheeling diode used. In summary, the proposed technique makes it possible to use devices with low forward voltage drop for high frequency applications. This also imply cheaper cost of devices as less processing steps are required during the manufacturing stages where the need of carrier lifetime control techniques are reduced.
"References"
1.S. Eio., N. Shammas., “IGBT Tail Current Reduction by Current Injection,” 43rd International Universities Power Engineering Conference, Padova, Italy,1 – 4 September 2008
2.S. Eio., N. Shammas., “A chopper circuit with current injection technique for increasing operating frequency,” 9th International Seminar On Power Semiconductors, Prague, Czech Republic, 27-29 August 2008
3.S. Eio., N. Shammas., “Switching Transient of Power Diode,” 41st International Universities Power Engineering Conference, Newcastle, United Kingdom, 6 - 8 September 2006, Volume 2, P. 564 – 568, Digital Object Identifier 10.1109 / UPEC.2006.367541
4.N. Shammas., S. Eio., “A Novel Technique to Reduce the Reverse Recovery Charge of a Power Diode,” 12th European Power Electronics and Applications, EPE 2007, Aalborg, Denmark, 2 - 5 September. 2007 P.1 – 8, Digital Object Identifier 10.1109 / EPE.2007.4417713
5.N. Shammas., S. Eio., “A Novel Technique to Reduce the Reverse Recovery Charge of a Power Thyristor,” 42nd International Universities Power Engineering Conference, Brighton, United Kingdom, 4 – 6 September 2007, p.1222 – 1227, Digital Object Identifier 10.1109 / UPEC.2007.4469126
6.N. Shammas., S. Eio., D. Chamund., “Semiconductor Devices and Their Use in Power Electronic Applications,” World Scientific and Eng. Academy and Society, Venice, Italy, 21 -23 Nov 2007
7.N.Shammas, S.Eio, S.Nathan, K.Shukry, D.Chamund., “Thermal Aspects of Power Semiconductor Devices and Systems,” VII Conference Thermal Problems in Electronics, MicroTherm’07, 24th – 28th June 2007, Lodz, Poland